.

.

New
fosa 20Hz-400Hz 5 V 0-5A AC Akım Algılama Sensörü Röle Modülü ile Ayarlanabilir Aşırı Akım Sinyal Ayarı Kritik Nokta

fosa 20Hz-400Hz 5 V 0-5A AC Akım Algılama Sensörü Röle Modülü ile Ayarlanabilir Aşırı Akım Sinyal Ayarı Kritik Nokta

₺ 35.37

Sayısı
İşlenmemiş

5 A aşırı akım koruma sensörü modülü.Röle aşırı akım sinyal çıkışını 0-5 A içinde elde etmek için AC sinyalini toplamak için akım transformatörünü kullanır.Aşırı akım sırasında röle çekme, aşırı akım değilken röle serbest bırakılır.Kullanıcılar, aşırı akım koruması elde etmek için harici devreyi açıp kapatmak için röle COM, NC, NO üç bağlantı noktasını kullanabilir.Aşırı akım sinyali ayarı kritik nokta ayarlanabilir.Şartname : Tipi : 5 A 12 V Röle Modülü Çalışma gerilimi : DC12 V Çalışma akımı : Körük olarak : 1. Kabloyu akım trafosundan ölçün, VCC ve gnd'yi DC12 V güç kaynağına bağlayın; 2. Röle çekme sesi (multimetre ile ölçülen, eğer COM ve açık olup olmadığını görmek için olabilir) duyunca potansiyometre ayarlamak, ve eğer röle bağlı ise aktif hale gelir, o zaman azaltmak veya bu test kablo vasıtasıyla , eğer aşırı akım koruma noktası (COM ve NC bağlı ise röle bağlı olmadığını görmek için olabilmesi kullanabilirsiniz belirlenmiştir şu anda geçiş serbest demekse serbest akım akan kesilmiş).

Ürün hakkında

Type:
5A 12V Relay Module
Working voltage:
DC12V
Working current:
Operating frequency range:
20Hz-400Hz
Output mode:
switch signal output
Maximum detection wire diameter:
5.2mm
Mounting hole:
hole diameter is 3mm, hole pitch is 52.5mm
Operating environment:
-40 - 85
Current detection range:
AC0.3A-5A
Board size:
Approx. 38 * 44mm / 1.5 * 1.7in
Weight:
Approx. 27g
Package list:
1 * Module :
Functions:
Current detection resolution can change the parameter of resistance parameters. :
Output over-current switching signal output. :
Over-current signal setting critical point is adjustable. :
Board Description:
VCC:
Operating voltage positive;
GND :
Operating voltage negative;
NO:
Normally open, the relay pulls before the NO and COM disconnect, short-circuit after the suction;
COM:
common, relay common interface;
NC:
Normally closed, the relay before the NC and COM short-circuit, after pull off.
Using Instructions:
By setting the potentiometer to set the overcurrent protection point, the clockwise adjustment can reduce the detection current. :
As bellows:
1. Measured the wire through the current transformer , connect VCC and GND to DC12V power supply; :
2. Adjust the potentiometer, when you hear the sound of the relay pull (can be measured with a multimeter, to see if COM and NO was turned on, and if connected to the relay means activated), then reduce or cut off the current flowing  that through the tested wire , if the relay release at this time that over-current protection point has been identified (can use multimeter to see if COM and NC was connected, if connected to the relay means been released) :
Son

Benzer teklifler